For detailed product specs see our NEW site at

http://www.artusaindustries.us

Alum-A-Frame

The simple solution to small and medium applications. 

Our patented Alum-A-Frame system can be configured to any application. 

It can be shipped knocked down or assembled.

Installation is straightforward and seldom requires special lifting equipment.

GENERAL INSTALLATION GUIDELINES:

One person can assemble this enclosure, however depending upon the size of the enclosure, two people may be needed to install larger panels. Use safety precautions and proper lifting techniques when handling panels.

To assemble your enclosure, you will need the following tools:

  RUBBER MALLET                 3/16” ALLEN WRENCH

  TAPE MEASURE                   METRIC ALLEN SET

  JIG SAW (OR SIMILAR)        ADJUSTABLE WRENCH

STEP 1- Layout of Components

Lay out frame components. Note the positioning of the corner fitting when assembling it to the aluminum profile extrusion. There are three branches to a corner, two that are closed and are identical, and a thrid which is open and notched. See the picture to the right. This thrid branch must be the vetical leg when assembling the frame.

STEP 2-Assembling the Frame

Asemble panel profile extrusion to corner fittings by tapping the corner onto the profile. Use caution when assembling the frame so that the aluminum profiles do not become bent or damaged. It si recommended that a wooden block be used to protect the aluminum corners from being damaged when hammering the frame together.

 NOTE: Components assemble in a “press-fit” fashion. Self-drill/tapping sheet metal screws are recommended to fasten the corners to the profile for added stability and in case where all panels are removable. The screws that fasten the extrusion to the fitting should be placed to the interior.

STEP 3 Installing Modular Panels with “retaining clamps” with Panel retaining clamps (Part no. U305) as shown in figure 3C.

STEP 4-Order of Installation and Location of Panels

(Referred to as “Direction of Erection,” or DOE). All panels are marked with a reference number. Below is the location of each panel and the order in which they need to be installed. Panels are installed on order from left to right.

NOTE: Doors are installed LAST and only after enclosure has been squared. When fastening fixed panels to frame, ensure that enclosure is square prior to fastening with supplied sheet metal screws.

 

50 Series For up to 2" Panels. Nominal 2-3/4" Extrusion Cross-Section Corner C-50 Profile P-50 Omega OM-50 Omega Joint OMJ-50 Bracket B45/50

Item Description Unit Remarks Corner, C-50 Each 8 corners required for a 4 sided enclosure. Profile, P-50 20' lengths Consult factory for cut to length profiles. Omega, OM-50 20' lengths Omega section used to frame openings & doors. Omega Joint, OMJ-50 Each Omega joint for attachment of omegas & profiles. Omega Bracket, B-45/50 Each Used to attach omega sections, 1 per joint Door Opening Bracket

 

45 Series For up to 1-7/8" Panels. Nominal 2" Extrusion Cross-Section

Series 45 Enclosures.  Prices are based on the following specifications with additional options available as listed.  Prices exclude freight and taxes.   ·       Alum-a-frame design with removable panels for access on two long sides. Acoustical panels are 16 ga. Galvanized steel.  Walls and roof filled with 2” acoustical absorption and lined with 22 ga galvanized perf. Removable panels lined with acoustical foam to reduce weight.  Includes 120 V fan and vent hood for heat rejection and inlet/discharge cfm.   One piping penetration is included. ·       Enclosures are fully assembled and skidded(if over 10’ in any direction check with factory for availability) ·       If removable panel height is over 7’ high a header may be required.  See below. ·       Standard wind loading-70mph can go higher as an option. ·       Standard submittal drawing lead-time is 1 week. Standard lead-time from approval is 3-4 weeks.   Square footage is based on the outside dimensions of the enclosures rounded to the nearest square foot.  Weight of skidded enclosure can be estimated at 5 lbs/ square foot for freight purposes.   A. <100 square feet use 23.00/square feet B. <150 square feet use 21.00/square feet C.              <200 square feet use 19.00/square feet D.              <250 square feet use 18.25/square feet E.              <350 square feet use 17.50/square feet F.               <450 square feet use 16.50/square feet G.             >450 square feet use 15.80/square feet H.              Option-50Hz fans, single phase, 20-75 hp units $200.00 I.                Option-50Hz fans, single phase, >75 hp units $50.00 J.               Option-220V fans on 20-75 hp units $225.00 K.              Option-220V fans on >75 hp units $25.00 L.              Door-36”wide x up to 84” high, $375.00 M.             Double Door-72” wide x up to 84” high, $730.00 N.              Header-$20.00 per linear foot. O.             Aluminum Construction Option-Base Price X1.18 P.               Deduct for 1 ½” acoustical foam instead of perf, $0.30 per square foot. Q.             Adder for additional openings, $ 95.00 R.              Adder for 4” walls-Base price X 1.1 S.               Adder for removable panels lined with perf-Base price x 1.05 T.              Enclosure Exterior Painted Pre-coated Galvanized Steel Option-Base Price X 1.22 U.              Stainless Steel Option-Base Price X 2.25 V.              3 phase fans and explosion proof fans – consult IES W.            Special construction or specifications- consult IES Quantity discounts (more than 3 of same size and design) or special pricing-consult IES   Item Description Unit Remarks Corner, C-45 Each 8 corners required for a 4 sided enclosure. Profile, P-45 20' lengths Consult factory for cut to length profiles. Omega, OM-45 20' lengths Omega section used to frame openings & doors. Omega Joint, OMJ-45 Each Omega joint for attachment of omegas & profiles. Omega Bracket, B-45/50 Each Used to attach omega sections, 1 per joint Door Opening Bracket DB-45/50 Each Connects Omega to profile & provides floor anchor, 2 per door

25 Series For up to 1" Panels. Nominal 1-1/4" Extrusion Cross-Section Corner C-25 Profile P-25 Omegas (OM-25 & OMS-25) w/bolt track A: OM-25 = 1.968 Use Omega Joint OMJ-25 shown below. A: OMS-25 = 1.18 No Omega Joint Available. Omega Joint OMJ-25 Three Branch Tee T3-25 Four Branch Tee T4-25

Series 25 Enclosures.  Prices are based on the following specifications with additional options available as listed.  Prices exclude freight and taxes.   ·       Alum-a-frame 25 series design with removable panels for access on two long sides. Acoustical panels are 16 ga. Galvanized steel.  Walls and roof filled with 1” acoustical foam.  Includes vent hood for heat rejection and inlet/discharge cfm.   One piping penetration is included if in same panel as vent hood ·       Enclosures are fully assembled and skidded(if over 6’ in height check with factory for availability) ·       Standard wind loading-70mph can go higher as an option. ·       Standard submittal drawing lead-time is 1 week. Standard lead-time from approval is 3-4 weeks.   Square footage is based on the outside dimensions of the enclosures rounded to the nearest square foot.  Weight of skidded enclosure can be estimated at 5 lbs/ square foot for freight purposes.   A. <    50   square feet use 21.00/square feet B. <    100 square feet use 16.75/square feet C.              >/= 100 square feet use 14.50/square feet D.              Option-120 V fans, single phase, 20-75 hp units $200.00 E.              Door-36”wide x up to 72” high, $260.00 F.               Aluminum Construction Option-Base Price X1.18 G.             Adder for additional openings, $ 75.00 H.              Enclosure Exterior Painted Pre-coated Galvanized Steel Option-Base Price X 1.22 I.                Stainless Steel Option-Base Price X 2.25 J.               3 phase fans and explosion proof fans – consult IES K.              Special construction or specifications- consult IES L.              Quantity discounts (more than 3 of same size and design) or special pricing-consult IES       Item Description Unit Remarks Corner, C-25 Each 8 corners required for a 4 sided enclosure. Profile, P-25 20' lengths Consult factory for cut to length profiles. Omega, OMS-25* 20' lengths Omega section used to frame openings & doors. Omega, OM-25 20' lengths Omega section used to frame openings & doors. Omega Joint, OMJ-25 Each Omega joint for attachment of omegas & profiles. Three Branch Tee, T3-25 Each Three Branch Tees for multi-cell enclosures Four Branch Tee, T4-25 Each Four Branch Tees for multi-cell enclosures. * Omega Joint unavailable for Omega OMS-25. Side flanges must be cut for propper fit. See assembly detail.

Home of the Most Versatile Noise Control and Environmental Enclosure and The Alum A Frame Enclosure, Air Pollution Control Equipment, Noise Control, Noise Abatement, Noise Absorbers, Noise Attenuation, Sound Control, Machine Enclosures, Acoustical Baffles, Acoustical Foam, Noise Barriers, Acoustical Wall Panels, Consulting, Surveys, Noise Control Buildings, Installation, Service, Demolition and Construction.

The best in Sound Enclosures, Noise Abatement, Noise Control, Acoustical Materials, Air Quality products and In-plant Offices.

Acoustical Enclosures, Weather-tight Enclosures, Humidity Control Enclosures, Portable Enclosures, Curtain Enclosures, Smoke Capture Enclosures, Mist Control Enclosures, Dust Collection ......for Blowers, Clean Rooms, Chippers, CNC centers, Compressors, Fans, Generators, Granulators, Grinders, Molders, Planers, Pumps, Test Cells, Turbines, Work Stations ...... any noise source. 

We get  rid of machine noise 85dBA and below